Which Diamond Stropping Compound Should I Use?
The short answer
If you only buy one compound, make it 1 micron or 0.5 micron. They're the best all-rounders. They're fine enough to leave a properly refined, very sharp edge, and still quick enough to clean up an edge without endless passes.
The other grits are for specific jobs. Go coarser (9 or 6 micron) to deal with stubborn burrs. Go finer (0.25 and 0.1 micron) to chase a mirror polish or the last bit of sharpness.
What stropping is actually for
A lot of advice online treats the strop as the place to get rid of the burr. It isn't. The burr should be kept as small as possible on the stones. Use lighter pressure as you finish each stone, and make sure the burr is gone before you move on.
What's left after a good stone finish is a tiny micro burr, too small to feel easily, that still rolls and dulls the edge quickly. That's what the strop is for. A few light passes on a diamond-loaded strop take off the micro burr and refine the apex, so the edge cuts cleanly and lasts.
If you're relying on the strop to take off a big, obvious burr, the strop might not even remove it, and you can end up just rounding the edge. Go back to the stones.
Stubborn, gummy burrs
Some knives fight back. Steel with a poor heat treatment, especially one that leaves a lot of retained austenite, tends to form a soft, gummy burr. Ideally a burr is abraded away rather than broken off, but high retained austenite makes it flexible, so it bends from side to side and more stone work just moves it around.
The proper fix is to joint the edge and re-apex it. Lightly run the edge straight down on the stone to remove the weak steel, then sharpen back up to a fresh apex with lighter pressure. That gets you below the damaged layer instead of chasing the burr around.
A coarse compound (9 or 6 micron) can sometimes help here too. Its stronger cutting action can take off a burr that finer grits just push around. If it doesn't clear after a few passes, joint and re-apex rather than stropping harder.
Getting a mirror polish
Working through a progression gets you to a mirror faster than jumping straight to the finest grit. Each compound removes the scratches left by the one before, so the finer grits only have small scratches to polish out instead of deep ones.
A typical progression after your stones is 6 → 4 → 1 → 0.5 → 0.25 micron, with 0.1 micron as an optional last step. Use a separate strop for each grit so coarse diamond never ends up on your fine strops. The colour coding makes it easy to keep them apart.
By around 0.25 micron the mirror is near flawless. 0.1 micron is there if you want to take it as far as it goes.
Pushing for extreme sharpness
You don't need the finest grit to get a frighteningly sharp edge. 1 micron and 0.5 micron can take an edge to tree-topping hair, where the edge cuts a hair held only at one end.
It is easier to get there at 0.25 micron, though. The finer finish leaves less to tidy up, so you'll hit that level of sharpness more often and with less fuss.
Quick picker
| What you want | Compound |
|---|---|
| One compound that does it all | 1 micron or 0.5 micron |
| Clear a stubborn or gummy burr | 9 or 6 micron (then joint and re-apex if it won't shift) |
| A step between coarse and fine | 4 micron |
| A mirror polish | Work down through the grits to 0.25 micron |
| The last bit of polish | 0.1 micron |
| Extreme sharpness, easier | 0.25 micron |
| Try a grit before committing | 5ml bottle, any grit |
Matching a compound to your stones
Stone grits aren't measured the same way across brands, so look up your last stone on our sharpening grit chart to see roughly what it is in microns. In practice it matters less than you might think. The strop's soft surface makes the diamond cut shallower than the same grit would on a stone, so 1 or 0.5 micron is a good place to start whatever your last stone was. If you're chasing a mirror polish, starting on a coarser compound and working down can make sense.
Shop the compounds 9 micron · 6 micron · 4 micron · 1 micron · 0.5 micron · 0.25 micron · 0.1 micron · 5ml bottles, any grit